Talk to an expert

Tell us what you need and we will call you back.

🇮🇳 +91

    Stock audit glossary · Textiles

    Shade Lot

    noun · also called a dye lot or shade batch

    Definition

    A shade lot is a quantity of fabric or yarn dyed together in one batch, so its colour matches throughout. Material of the same specification from another lot can differ in shade enough to show when the two are placed side by side, so usable stock is counted lot by lot, not just by item code.

    • Reviewed by CA Sundram Gupta · Chartered Accountant
    • Last reviewed 23 October 2026
    • 5 min read

    See related terms

    At a glance

    Is
    One dye batch Colour matches within it
    Across lots
    Shades can differ Visible side by side
    Recorded
    On every roll ticket and in the system So it survives a lost label
    Orders filled
    From one lot Or lots checked to match
    Leftovers
    Small part-lots Often sell below cost

    Meaning

    01 What a shade lot is

    Dyeing is done in batches, and colour matches within a batch, not across batches. The difference between two batches can be small enough to pass a quality check and still show at the seam of a garment cut from both.

    So an item code is not the same as a usable quantity. A large holding of one code spread over many small lots may not fill a single normal order, because the customer needs matching cloth, not a total. A count therefore records the lot with the quantity, and small leftover lots, which age without moving, are where the valuation questions start.

    Where it matters

    02 Where shade lots matter, and what they change in the record

    Wherever colour is applied in batches.

    Where lots matter

    • Textiles and garments. Panels from different dye lots show a mismatch at the seam.
    • Yarn and thread. A lot difference carries into everything made from it.
    • Tiles, paints and laminates. A floor, wall or surface finished from two batches can show a line.

    What changes in the stock record

    • The lot on every roll. Printed on the ticket and held in the system.
    • Storage by lot. Matching quantity can be read straight off the rack.
    • Availability by lot. The largest matching group, not the code total, is what an order can draw on.
    The code says what; the lot says which. Both are needed before a quantity can be promised to a customer.

    In practice

    03 How shade lots work in practice

    Code totalOff-shade lotsUsable
    Input Where it comes from Sample (metres)
    Code total The stock record for the design, all lots 3,200
    Lots outside tolerance A shade check of each lot against the main lot 900
    Usable together The largest group of matching lots 2,300

    3,200 − 900 = 2,300 metres that can go into one order. Sample figures for illustration only.

    From dye house to cutting table

    1. Number the lot at dyeing

      Cloth or yarn dyed together is given one lot identifier.

    2. Ticket every roll

      The lot is printed on each roll ticket and entered in the stock record, so it survives a lost label.

    3. Store by lot

      Rolls are grouped by lot on the rack.

    4. Fill each order from one lot

      Or from lots checked to match each other.

    5. Count by lot

      Quantity is recorded against lot and code; part-lots too short for a customer’s smallest order are set aside, because they sell for less.

    Worked example

    04 One design, three lots

    Sample figures.

    A garment unit holds 5,450 metres of one printed design across three dye lots, valued at 136 per metre
    Lot Metres Value (INR)
    Lot 4417-A, within tolerance 2,400 3,26,400
    Lot 4417-B, within tolerance 1,850 2,51,600
    Lot 4419-C, visible variation 1,200 1,63,200
    Total for the design 5,450, of which 4,250 usable as one 7,41,200

    The total adds up but cannot be sold as stated

    The system shows one code with 5,450 metres, so an order for 5,000 metres is accepted. It cannot be filled: lot 4419-C will not match the other two in one garment, so only 4,250 metres can serve that order.

    If the record does not hold the lot, the stock figure is right and still misleading, and the problem is found at cutting rather than at counting.

    Watch out

    05 Common mistakes with shade lots

    Most errors come from treating the item code as the unit of stock.

    Adding a code across all lots

    A total is offered that no single order can use.

    Show availability lot by lot.

    The lot on the ticket only

    The information goes with a lost label.

    Hold the lot in the system too.

    Re-ticketing without the lot

    Inspection breaks the link to the dye batch.

    Carry the lot onto every new ticket.

    Remnants from several lots on one ticket

    None of them can be matched afterwards.

    Keep remnants ticketed lot by lot.

    Reading the bay label

    Mixed lots in one bay are counted as one.

    Read each roll ticket at the count.

    Small part-lots at full rate

    Cloth that cannot fill a minimum order is overvalued.

    Review leftover lots for their value.
    CA Sundram Gupta

    Reviewed by CA Sundram Gupta · Chartered Accountant

    Patron Accounting LLP. This page makes no regulatory statement.

    Last reviewed: 23 October 2026 Applies to: textile mills, processors, garment makers and traders holding dyed fabric or yarn

    Sources: general textile stock-control practice; no statutory statement is made on this page. General information, not professional advice.

    Need help with shade lots? See our textile stock audit service. A textile stock audit records dyed fabric by lot as well as by design.

    Talk to an expert

    Tell us what you need and the right person calls you back.

    🇮🇳 +91

      By sending this form you agree to our privacy policy.