Talk to an expert

Tell us what you need and we will call you back.

🇮🇳 +91

    Stock audit glossary · Stores and records

    Tool Crib

    noun · also “tool store” or “tool room”

    Definition

    A tool crib is a controlled store inside a workshop that issues tools, cutting inserts, gauges and similar items to operators against a record, with many of them expected back. It exists because these items are small, portable and easy to lose, so control is applied at the moment of issue rather than only through occasional counts.

    • Reviewed by CA Sundram Gupta · Chartered Accountant
    • Last reviewed 23 October 2026
    • 6 min read

    See related terms

    At a glance

    Holds
    Tools, inserts, gauges Small, portable, easy to lose
    Control point
    The moment of issue Who took it, for which job
    Above the threshold
    Item by item Returnable items chased back
    Below the threshold
    Consumption ratios Use per unit of output
    Run by
    A named crib keeper Accountability starts there

    Meaning

    01 What a tool crib is

    Some items are too portable to control by counting them now and then. Inserts, gauges, hand tools and measuring instruments go missing one at a time, and no single loss seems worth chasing; a stocktake months later can only report a total difference nobody can explain. Control at the point of issue fixes this: items go out against a record of who took them and for which job, often with an expectation of return, so accountability starts the moment an item leaves.

    The practical question is where to draw the line. Recording every washer slows the shop floor and is soon abandoned. A workable crib controls higher-value and returnable items one by one and manages the rest through consumption ratios, which measure total use against production without recording each issue.

    Where it is used

    02 Which sectors use a tool crib

    Wherever portable tooling is issued to people.

    Where it is common

    • Engineering, machine tools and auto components. Cutting tools, inserts and gauges are always in circulation.
    • Heavy fabrication and shipbuilding. Hand tools and instruments issued across large sites.
    • Maintenance teams and construction. Tools and power equipment drawn for a job and returned.

    Where it is not needed

    • Fixed tooling. Every tool stays with its station.
    • Warehousing and retail. Equipment in use is low in value and narrow in range.
    • Office-based work. No portable tooling is issued.
    It suits operations where valuable, portable tooling is issued to people rather than fixed to machines.

    In practice

    03 How a tool crib is run

    IssuedOutputPer 1,000
    Input Source Sample
    Inserts issued in the month Crib issue record 1,860
    Components machined Production records 2,40,000
    Usual ratio, last quarter The same calculation, earlier months 6.2
    Inserts per 1,000 components Higher than usual: check before concluding 7.75

    1,860 ÷ 2,40,000 × 1,000 = 7.75, against a usual 6.2. A harder material or a new job may explain it; if not, issues are being lost. Sample figures for illustration only.

    Setting up and running the crib

    1. Set up a store with a named keeper

      Holding tooling, gauges, inserts and measuring equipment.

    2. Fix a value threshold

      Items above it are issued one by one against the person and job; items below are controlled in total.

    3. Mark returnable items as returnable

      So the record itself prompts someone to ask where they went.

    4. Track low-value use as a ratio

      For example inserts used per thousand components made.

    5. Count, trace and check

      Count controlled items fully and sample the rest; trace differences through the issue records and check ratio changes against production first.

    Worked example

    04 Three kinds of tooling, three ways to verify

    Sample figures.

    A machine shop’s tooling held in a controlled store (sample)
    Category and items Value (INR) Issued and verified
    Cutting tools, consumable · 4,200 18,00,000 Against a job card, not returned · by count
    Gauges and instruments · 310 26,00,000 To a named person, returnable · by count and calibration
    Fixtures and jigs · 96 41,00,000 To a machine, semi-permanent · by sighting
    Total · 4,606 85,00,000 Three methods, not one

    Present is not the same as fit to use

    Consumable cutting tools are stock: issued, used up and never returned. Fixtures behave more like fixed assets, staying with a machine for a long time.

    Gauges are returnable but useless if out of calibration, so finding all 310 proves only part of what is needed. A crib treated as one store tends to count everything and calibrate nothing, which can leave 26,00,000 of instruments present and recorded but not fit to measure with.

    Watch out

    05 Common mistakes with a tool crib

    Too much control fails as surely as too little.

    Paperwork for every minor item

    Production slows and the system is dropped.

    Control in total below a value threshold.

    A threshold set once and forgotten

    Rising prices move whole categories across the line.

    Review the threshold at least yearly.

    No named keeper

    The accountability the crib exists for disappears.

    Name one keeper and a deputy.

    Returnables issued as if consumed

    Nobody is prompted to ask for them back.

    Mark returnable items on every issue.

    Counting and just adjusting

    Unrecorded issues cannot be traced and nothing is explained.

    Trace differences through the issue records first.

    No consumption ratios

    Low-value use is never measured at all.

    Track use against production every month.

    Questions

    06 Tool crib FAQ

    What is tool crib management?

    Tool crib management is running the crib so every tool can be accounted for. It covers issuing and taking back items against a record of the person and the job, setting the value threshold for item-by-item control, tracking use of low-value items against production, and counting the crib from time to time.

    Is being a tool crib attendant hard?

    The work is less about physical effort than about discipline. An attendant issues and receives items all shift, records each one against a person and a job, follows up returnable items that have not come back, and keeps the store in order for counts. Accuracy and persistence matter more than strength.

    CA Sundram Gupta

    Reviewed by CA Sundram Gupta · Chartered Accountant

    Patron Accounting LLP. This page makes no regulatory statement.

    Last reviewed: 23 October 2026 Applies to: workshops and plants issuing tooling, gauges and instruments, and the auditors who count them

    Sources: general stores and workshop practice; no statutory statement is made on this page. General information, not professional advice.

    Need help with a tool crib? See our stock audit service. A stock audit verifies tooling by count, calibration and sighting.

    Talk to an expert

    Tell us what you need and the right person calls you back.

    🇮🇳 +91

      By sending this form you agree to our privacy policy.